Page 1 of 1

12v rzr lights done

Posted: Tue Feb 12, 2019 3:29 pm
by Jkilmurray
I got the lights done on the kids new rzr. Pretty much just eagle eye leds all the way around. 2 in each headlight. 1 in each roll bar light and 1 red one in each tail. I also used 2 red strip lights in each tail to give it a nicer look. Went with yellow strip lights in each wheel well as well. Ran it to 3 separate switches to control head/tail, underglow, and roll bar lights. Had to get the low profile 23mm eagle eyes to fit under lenses. Ended up using same in roll bar lights. Cut some plexi and silicones into the roll bar lights to set them back as far as I could to get better light output. Pics don’t really do it justice. Can’t really see the details in the lights.
598CA6EE-8B40-4B2F-94EE-9F1F0DB4B11E.jpeg
598CA6EE-8B40-4B2F-94EE-9F1F0DB4B11E.jpeg (2.88 MiB) Viewed 1282 times
330A59FF-B75D-4A2D-9860-5A69A60D0509.jpeg
330A59FF-B75D-4A2D-9860-5A69A60D0509.jpeg (2.98 MiB) Viewed 1282 times
46EA629E-CEA9-483E-A6CD-A0D7E62B5A72.jpeg
46EA629E-CEA9-483E-A6CD-A0D7E62B5A72.jpeg (2.52 MiB) Viewed 1282 times
B1602661-4627-4C29-A37F-E8A3F8E9C2FF.jpeg
B1602661-4627-4C29-A37F-E8A3F8E9C2FF.jpeg (1.81 MiB) Viewed 1282 times
2FD28E8A-EFD7-42A6-884B-5ED2B8E783DA.jpeg
2FD28E8A-EFD7-42A6-884B-5ED2B8E783DA.jpeg (2.37 MiB) Viewed 1282 times
943D9E72-3AFB-43D2-B53F-E51B6FAD8E28.jpeg
943D9E72-3AFB-43D2-B53F-E51B6FAD8E28.jpeg (2.36 MiB) Viewed 1282 times
26D81A4C-2448-4F20-813B-E5BC1E45F3CD.jpeg
26D81A4C-2448-4F20-813B-E5BC1E45F3CD.jpeg (2.15 MiB) Viewed 1282 times
59EA677E-A107-4DD1-87C0-3985152721A5.jpeg
59EA677E-A107-4DD1-87C0-3985152721A5.jpeg (2.83 MiB) Viewed 1282 times
E094517B-C8DC-4573-99D7-E36837B7B157.jpeg
E094517B-C8DC-4573-99D7-E36837B7B157.jpeg (2.36 MiB) Viewed 1282 times

Re: 12v rzr lights done

Posted: Tue Mar 05, 2019 3:02 am
by LightningMcQueen
Looks great! Do you have a diagram of how you ran everything?

Re: 12v rzr lights done

Posted: Tue Mar 05, 2019 9:07 am
by Jkilmurray
No diagram. Just ran all the rear lights to the center where the stock wires are under the little plastic cover. Ran the rear and the front into the battery compartment and ran to switches. On the light bar I drilled some holes under where they screw in and ran them inside the roll bar down and out. If you need any kind of pics I’d be happy to send you some. I didn’t mess with the terminal blocks or anything. Just ran wires direct.

Re: 12v rzr lights done

Posted: Tue Mar 05, 2019 12:42 pm
by LightningMcQueen
Awesome! Looks good! Did you notice any draw in power when they were on?

Re: 12v rzr lights done

Posted: Tue Mar 05, 2019 3:00 pm
by Jkilmurray
Didn’t notice any. But I switched to 18v at the same time.